- Read and understand "Change Spec. Card Procedure"
- Read and understand "Non-Conforming Product Procedure"
- Get magnets from magnet board that contains the work order information for production
- Locate pallet or cart with the WOR folder containing the corresponding material, work order numbers and instructions
- Determine and obtain the correct tool for the job identified on the Spec. Card from the tooling rack
- Remove tooling from box, attach bearer blocks and slide into tooling station
- Set the machine for the appropriate job
- Retain Supplier raw material tag with lot # and run # information along with "Approved for Use" tags on separate sheet of paper (if only using partial material and retuning excess material do not retain tag, just record part #, lot # and run # on sheet)
- Complete "Sign-off Check List" (if operator has less than 1-year experience, needs sign-off from experienced operator with over 1 year experience)
- Print out (core tags or box tags) along with 1st piece and last piece labels with correct information,
- Make sure the right material is used where needed, to the proper side of the liner and in the right orientation
- Place material in machine. Feed it through the fife guide and adjust it for center run.
- Place adhesive in machine and line-up with materials so that they are even with each other
- Start machine, adjust tension and alignment as needed
- Pass the material through to the die cutting station
- Remove any waste or air-injection from the tool
- Adjust nip-roller speed for proper speed and dimensions of part
- Verify part to print and or mylar and record dimensions
- Retain first approved piece and place label on back side
- Complete In-Process check sheet during the run.
- Complete End-of-Run sign off confirming the required parts were produced.
- Retain last approved piece and label back side
- Maintain a clean and safe work area, cleaning floor, machine, work area at end of each job and at end of shift
- Cut cores for particular jobs when needed. Obtain boxes and materials necessary for job
- Operate production equipment to produce good, quality product in an efficient/quality-oriented manner.
- Makes suggestions for ways to improve production process
- Works with sales and estimating to test/run samples for new product introduction
- Makes sure product being produced matches the spec card and the degree of quality needed (tolerances etc..)
- Updates spec card for future runs when process is changed
- Observe machine operation to detect workpiece defects or machine malfunctions; adjust machines as necessary.
- Change worn machine accessories such as cutting tools and brushes, using hand tools.
- Perform minor machine maintenance, such as oiling or cleaning machines, changing filters or adding lubricant to the Rotary press when necessary.
- Notify supervisors when major service is required.
- Other duties as assigned.
- Read and understand "Change Spec. Card Procedure"
- Read and understand "Non-Conforming Product Procedure"
- Get magnets from magnet board that contains the work order information for production
- Locate pallet or cart with the WOR folder containing the corresponding material, work order numbers and instructions
- Determine and obtain the correct tool for the job identified on the Spec. Card from the tooling rack
- Remove tooling from box, attach bearer blocks and slide into tooling station
- Set the machine for the appropriate job
- Retain Supplier raw material tag with lot # and run # information along with "Approved for Use" tags on separate sheet of paper (if only using partial material and retuning excess material do not retain tag, just record part #, lot # and run # on sheet)
- Complete "Sign-off Check List" (if operator has less than 1-year experience, needs sign-off from experienced operator with over 1 year experience)
- Print out (core tags or box tags) along with 1st piece and last piece labels with correct information,
- Make sure the right material is used where needed, to the proper side of the liner and in the right orientation
- Place material in machine. Feed it through the fife guide and adjust it for center run.
- Place adhesive in machine and line-up with materials so that they are even with each other
- Start machine, adjust tension and alignment as needed
- Pass the material through to the die cutting station
- Remove any waste or air-injection from the tool
- Adjust nip-roller speed for proper speed and dimensions of part
- Verify part to print and or mylar and record dimensions
- Retain first approved piece and place label on back side
- Complete In-Process check sheet during the run.
- Complete End-of-Run sign off confirming the required parts were produced.
- Retain last approved piece and label back side
- Maintain a clean and safe work area, cleaning floor, machine, work area at end of each job and at end of shift
- Cut cores for particular jobs when needed. Obtain boxes and materials necessary for job
- Operate production equipment to produce good, quality product in an efficient/quality-oriented manner.
- Makes suggestions for ways to improve production process
- Works with sales and estimating to test/run samples for new product introduction
- Makes sure product being produced matches the spec card and the degree of quality needed (tolerances etc..)
- Updates spec card for future runs when process is changed
- Observe machine operation to detect workpiece defects or machine malfunctions; adjust machines as necessary.
- Change worn machine accessories such as cutting tools and brushes, using hand tools.
- Perform minor machine maintenance, such as oiling or cleaning machines, changing filters or adding lubricant to the Rotary press when necessary.
- Notify supervisors when major service is required.
- Other duties as assigned.
-
Automatics Press Operator
1 week ago
Ridgeview Industries, Inc. Grand Rapids, United StatesIf you are looking for an organization committed to the principles of Excellence, Integrity, Faith, and Teamwork, then Ridgeview Industries offers a challenging and rewarding employment opportunity for you. · Ridgeview Industries is a leading metal stamping and assembly supplier ...
-
Press Operator
3 weeks ago
NESCO Inc Kent, United StatesPress Operator1st ShiftDIRECT HIREJOB SUMMARYApplies basic set-up and operation of forming presses to form sheet metal aircraft componentsas specified by written instructions and drawings. Inspects completed work for conformance tospecifications.Functions and ResponsibilitiesSet ...
-
Press Operator
2 weeks ago
NESCO Inc Kent, United StatesPress Operator · 1st Shift · DIRECT HIRE · JOB SUMMARY · Applies basic set-up and operation of forming presses to form sheet metal aircraft components · as specified by written instructions and drawings. Inspects completed work for conformance to · specifications. · Functi ...
-
Press Operator
1 week ago
Parker Kent, United StatesParker - Manufacturing [Manufacturing Technician / Production Associate] As a Press Operator at Parker, you'll: Operate presses and ovens to manufacture PTFE billets that will be machined into seals; Load, operate and unload molding presses to create billets for the CNCs to machi ...
-
Press Operator
3 weeks ago
Boyd Company Grand Rapids, United StatesJob DescriptionEssential Duties Include: Read and understand "Change Spec. Card Procedure"Read and understand "Non-Conforming Product Procedure"Get magnets from magnet board that contains the work order information for productionLocate pallet or cart with the WOR folder containin ...
-
Press Operator
3 days ago
Boyd Company Grand Rapids, United StatesEssential Duties Include: · * Read and understand "Change Spec. Card Procedure" · * Read and understand "Non-Conforming Product Procedure" · * Get magnets from magnet board that contains the work order information for production · * Locate pallet or cart with the WOR folder conta ...
-
Press Operator
2 weeks ago
Boyd Grand Rapids, United States Full timeJob Description · Essential Duties Include: · Read and understand "Change Spec. Card Procedure" · Read and understand "Non-Conforming Product Procedure" · Get magnets from magnet board that contains the work order information for production · Locate pallet or cart with the WOR ...
-
Press Operator
1 week ago
TeamWorld, Inc. Conklin, United States: · **REPORTS TO**: · Production Manager · **GENERAL JOB DESCRIPTION** · Responsible for learning and understanding all aspects of computer-controlled carousel style bottle screen printing machine. The operators' primary functions are to ensure the press is properly set up in a t ...
-
Night Shift Flexographic Press Operator
2 weeks ago
GREAT LAKES LABEL Comstock Park, United States**Flexographic Press operator** · **GENERAL PURPOSE**: Set up, operate, and maintain a multicolor Flexographic press including Mark Andy's, and Webtrons, using UV water base inks. Manage all aspects of press performance including productivity, quality and maintenance. · **ESSENTI ...
-
Press Brake Operator
1 week ago
American Workforce Group Kent, United StatesJob Description · Job DescriptionAre you PRESSED for a job and ready to BRAKE into a new position? · American Workforce Group is in search of a qualified Press Brake Operator in Kent, WA · If you are motivated, qualified individual we would love to speak with you · Details for Pr ...
-
Brake Press Operator
2 weeks ago
WorkSolved Staffing Grand Rapids, United StatesWorkSolved Staffing is recruiting for a Press Brake Operator at a client in Grand Rapids, MI. This is a full-time position with advancement potential. All shifts available. Great opportunity to learn and expand your skillset Air-conditioned environment. · Press Brake Operator Dut ...
-
Brake Press Operator
1 week ago
WorkSolved Staffing Grand Rapids, United StatesJob Description · Job DescriptionWorkSolved Staffing is recruiting for a Press Brake Operator at a client in Grand Rapids, MI. This is a full-time position with advancement potential. All shifts available. Great opportunity to learn and expand your skillset Air-conditioned enviro ...
-
Brake Press Operator
2 weeks ago
WorkSolved Staffing Grand Rapids, United StatesWorkSolved Staffing is recruiting for a Press Brake Operator at a client in Grand Rapids, MI. This is a full-time position with advancement potential. All shifts available. Great opportunity to learn and expand your skillset Air-conditioned environment. · Press Brake Operator Dut ...
-
Automatic Press Operator
1 week ago
Workbox Staffing Grand Rapids, United StatesJob Description · Job DescriptionAutomatic Press Operator - 2nd and 3rd Shift, $18.50+/hrA local, leading metal stamping and assembly supplier is looking for Automatic Press Operators for their 2nd and 3rd shiftsWilling to pay more for experienced Automatics OperatorsPrimary resp ...
-
Automatic Press Operator
1 week ago
Pridgeon & Clay Inc Grand Rapids, United StatesJob Description · Job DescriptionAre you looking for a challenging yet rewarding career that allows you to utilize your skills to their fullest potential? Do you want to join a team of hardworking, enthusiastic and creative people and enjoy working with a company that recognizes ...
-
Brake Press Operator
1 week ago
Metal Components Grand Rapids, United StatesJob Description · Job DescriptionJob Title: Press Brake Operator · Department: Manufacturing · Reports To: Shift Supervisor · FLSA Status: Non-exempt · SUMMARY · Set up and operate press brake to bend, notch, punch, form roll, arc or straighten metal plates or sheet metal, follow ...
-
Set Up Brake Press Operator
1 week ago
Elwood Staffing Grand Rapids, United StatesAn international manufacturer of point of purchase displays and decorative wire products is looking to add a Set-Up Break Press Operator to their team. Apply today to learn more Company Profile. Our client is an international manufacturer of point o Press Operator, Brake Press, P ...
-
Press Operator
3 weeks ago
WorkBox Staffing Rockford, United StatesPress Operator -$18 , 1st Shift - Rockford, MI A local company in Rockford is looking for a press operator Preferred Qualifications: Must be able to read a tape measure Run a press Lifting 35-50 pounds Preferred Skills:Good math skills In this role, Press Operator, Operator, Staf ...
-
Press Operator
3 weeks ago
PrideStaff Coopersville, United StatesPrideStaff seeks Automatic Brake Press Operator / Stamping - Coopersville. PAY: $ 17 - $20 / hour (BOE and shift premium)STARTS: ASAP after approval. ENDS: N/ A - Permanent hiring potential. HOURS: Full time / week (various shifts)SHIFT: Press Operator, Operator, Brake Press, Man ...
-
Press Operator
1 week ago
PrideStaff Coopersville, United StatesPrideStaff seeks Automatic Brake Press Operator / Stamping - Coopersville PAY: $ 17 - $20 / hour (BOE and shift premium) · STARTS: ASAP after approval · ENDS: N/A - Permanent hiring potential · HOURS: Full time / week (various shifts) · SHIFT: 1st, 6a-4:30p Mon-Thur-or- 2nd, ...
Press Operator - Grand Rapids, United States - Boyd Company
Description
Job DescriptionEssential Duties Include:
High school diploma or equivalent
Requirements
Essential Duties Include:
High school diploma or equivalent